How can the axial load-carrying capacity of a steel column be determined?
Following on from our previous article on evaluating the Euler buckling load, we’re going to look at some other calculations we need when looking at buckling of columns.
Eccentrically loaded steel column design.
The axial force can’t act centrically on the column, so, in addition, the column is always exposed to bending. As a result of the action of the bending moment, there is a further increase in the bending moment.
For the design of eccentrically loaded steel columns, the following conditions must be met:
NEdNcr,Nc,Rd +MEdMRd<1
Where:
- MEd=NEd x e
- e – eccentricity (m)
- MRd – design resistance bending moment, MRd=W·fyM0 (kNm).
Euler critical buckling force is defined as: Ncr=2EILe2
The Euler critical buckling force is defined as:
Ncr=2EILe2
Take a 3-meter-long column with one end pinned and the other fixed. It has a cross-section area of A = 3.125 x 10-3 m2, moment of inertia of I = 4.7526 x 10-5 m4, and a width of 2.20 x 10-4 m3. Column is loaded with NEd = 150 kN at eccentricity of e = 0.02 m.
We’re going to calculate the axial force and bending moment interaction for steel grade S235 and E = 210 x 109 Pa.
Nc,Rd=A x fyM0=0.003125 mm2 x 235 MPa1.1=667.6 kN
Le=K x L = 0.7 x 3.0m = 2.1m.
Ncr=2EILe2=9.86 x 210 x 109 Pa x 4.7526 x 10-52.12=223.14 kN
MEd=150 kN 0.02m=3.0 kNm
MRd=W x fyM0=2.2 x 10-4 m3 x 235 MPa1.1=47.0 kNm
NEdNcr,Nc,Rd +MEdMRd=150 kN223.14 kN+3.0 kNm47.0 kNm=0.67+0.064=0.734<1
The axial load carrying capacity of real columns.
Due to various imperfections of real steel columns, failure due to inelastic buckling occurs before the Euler buckling force. The procedure for determining the buckling load-bearing capacity of a real steel column consists of several steps:
- column plastic resistance calculation,
- column effective length determination,
- slenderness λ determination,
- slenderness λ1 determination,
- non-dimensional slenderness determination,
- buckling curve determination,
- reduction factor χ determination,
- column buckling load-bearing capacity calculation.
To consider geometric and material imperfections, dimensionless buckling curves were defined. The figure below shows dimensionless buckling curves.
Except for buckling curves, the reduction buckling factor (χ) can be calculated by the following expression:
χ=1ɸ+ɸ2-2<1.0
Where are:
ɸ=0.5·[1+α·̿-0.2+̿2]
Column buckling resistance (kN) is defined by the following expression:
Nb,Rd=χ x Nc,Rd.
Let’s check out another example. We’ll take another 3m long column with one end pinned and the other fixed. It has a cross-section area A=3.125×10-3 m2 and moment of inertia I=4.75026×10-5 m4. Buckling curve a. Calculate the column buckling resistance for steel grade S235 and E=210 x 109 Pa.
Nc,Rd=A x fyM0=0.003125 m2 x 235 MPa1.1=667.6 kN
Le=K x L=0.7 x 3.0m=2.1m
imin=IA=4.75026 x 10-50.003125=0.039 m
λ=Leimin=2.1m0.039m=53.8
1=π x Efy=3.14 x 210000 x 106 Pa235 x 106 Pa=29.9
=1=53.829.9=1.8
From the diagram above χ = 0.28.
Nb,Rd=χ x Nc,Rd=0.28 x 667.6 kN=186.9 kN
We’re going to finish off our series of buckling calculations in our next article, so be sure to check it out.
Interested in our courses?
Interested in civil or mechanical engineering? Find out more about all the civil engineering courses we have available by clicking here, and the mechanical engineering courses by clicking here.
Diploma in Mechanical Engineering
Diploma in Mechanical Technology
Diploma in Sustainable Construction
Diploma in Structural Engineering
Diploma in Building and Construction Engineering
Higher International Certificate in Civil Engineering
Higher International Diploma in Civil Engineering
Higher International Diploma in Mechanical Engineering
Higher International Certificate in Mechanical Engineering
Alternatively, you can view all our online engineering courses here.
Recent Posts
From Sparks to Strength: Top Welding Techniques You Should Know
From Sparks to Strength: Top Welding Techniques You Should Know Introduction From spark to structural bond—that’s the transformative power of welding. In the iLearn Engineering® article “From Sparks to Strength: Top Welding Techniques You Should Know,” readers are guided through essential welding methods—such as SMAW, MIG, TIG, and spot welding—each selected for strength, speed, or […]
Enhancing Materials: A Look into Surface Treatment Processes
Enhancing Materials: A Look into Surface Treatment Processes Introduction In manufacturing, selecting a material with the right bulk properties is only half the story. The performance of a component often hinges on what happens at its surface. The iLearn Engineering® article explores how various surface treatment processes—from coatings and plating, to shot peening, anodizing, and […]
How Material Removal Rate Affects Surface Quality and Production Speed
How Material Removal Rate Affects Surface Quality and Production Speed Introduction When machining components, one of the most critical—and often overlooked—factors is the material removal rate (MRR). It’s a common assumption that increasing MRR boosts productivity. However, as this iLearn Engineering article explains, this simple equation comes with important trade‑offs. Pushing MRR too high can […]